RC Servo Saver Installation and Troubleshooting

RC Servo Saver Installation and Troubleshooting!

Having an RC servo saver can reduce the chances of damaging your servo completely. While you might already know that, it’s important to know some details about servo savers.

Otherwise, you might encounter some troubles with installing it. 

So, do you know everything about RC servo saver installation and troubleshooting?

Installing and troubleshooting the servo saver requires a wrench and plier. Before you install the servo saver, you need to check the servo. After that, you can install the servo without much worry. However, you may need to fix your saver if it gets damaged. For that, you’ll need to identify the problem.

I know that’s just a brief. Are you interested to know all about the RC servo saver? 

Then what are you waiting for!

How to Check Servo Saver?

You’re probably most eager to know about installing the servo saver. I’ll definitely discuss all the details about it. However, before we arrive at that, you need to revaluate some criteria of the servo saver.

Source: gpmparts.com

If the servo saver is not good enough, then is there any point in installing it? That’s why you need to make sure your servo saver is top-class. So, I’ll start this installation guide by discussing the way of checking the servo saver.

The best way to check or test any servo saver spring is by adding stress to the unit. Now, how can you stretch the servo saver to test that?

Well, you can make your very own servo stretcher or can use a plier or wrench. All you need to do is to apply stress to the unit until it reaches its threshold. That way, you’ll be able to know how much shock it can absorb.

If your servo saver is not good enough, you can pick these premium servo savers. They have very good endurance and durability-

So, you’re all done with the checking and testing. It’s time to move on to assembling and setting it up for your servo.

How to Assemble & Set Servo Saver?

Hey there buddy! It’s great that you want to know how to assemble and set a servo saver. The assembling part is quite fun actually. It’ll almost feel like playing with legos! 

Don’t believe my words? Let me explain.

You’ll get three servo saver springs inside the saver. Now, assembling is basically sorting the three different-sized springs together. 

First, you’ll put the medium-sized spring behind the small one. And then repeat the process with the big one.

Source: rcjaz.com

That’s it! After that, setting your saver will require some thread lock fluid and your fingers. But be careful while using threadlocker in RC. Because they come in various colors and strengths.

Here are some thread locker that we’ve to work exceptionally well while assembling the servo saver:

Now, observe the gap between the two ends. Use your fingers to tightly place the saver in. Otherwise, you might face some steering problems.

Now, you’re completely ready to install the servo saver!

How to Install a Servo Saver?

Installing a servo saver onto your servo may seem troublesome at first. But that’s totally not the case. It’s true that you have to put some effort into it. There’s no denying that. However, once you see the outcome, you’ll be glad that you worked for it!

I’ll guide you through the full installation process thoroughly. Although the instructions may vary depending on your RC car, they share some similarities.

So, let’s look at the 3 steps easy guide to installing the servo saver-

Step 1 of 3: Take out The Tools

You obviously will need some basic tools before you can install the servo saver. The two tools you’ll need are a plier and a two-point-zero wrench. 

Step 2 of 3: Place the Spring Inside the Servo

There are a total of three springs that come with the saver. They are small, medium, and large-sized. 

Place those springs on top of another and put them inside the servo saver. Then, use the plier and wrench it to align them with the pocket.

Step 3 of 3: Screw it Tight!

The last thing on your installation guide! After closing the servo saver with the servo spine, you’ll just need to screw it in. Put it on your RC car and you’re done with the installation!

Source: traxxas.com

See? That’s how easy it is to install a servo saver. So, don’t worry too much and plug in a servo saver for your RC car.

How to Adjust Servo Saver?

You may have installed the servo saver but it’s not the end. Because there can be adjustment issues. So, it’s best for you to know about adjusting your servo saver.

The basic adjustment of the troubleshooting rc servo method is to look for a loose fit. To do that, turn on your radio and then your RC car. 

Raise one of the wheels and look at the steering servo arm. If it turns while the wheel doesn’t, then the servo saver is not fit enough. On such occasions, you’ll need to tighten your servo saver. 

On the other hand, if both the arm and wheel turn, then the adjustment is good. 

Are you itching to know how to make your servo saver tight as hell? Hop to the next segment right away!

How to Tighten Servo Saver?

Tightening up your servo saver is not that difficult, compared to the other troubleshooting. However, it does require some good observation. Or else, your RC car will not be able to operate perfectly.

As mentioned before, the fit can make your steering arm and wheel misaligned. And that’s a pretty big issue if in my opinion. So, without a good adjustment, your RC car will suffer.

Now, to tighten the servo saver, all you need is your hand, specifically, your fingers! Because servo savers are usually made to be as finger adjustable as possible. But for extra tightness, you can use theardlocker at the nut too.

One thing to keep in mind about the fit. Dirt or dust can get into the servo saver. And that can also make it come loose. So, try to clean your servo saver once in a while. It will benefit your whole RC car experience.

How to Fix a Servo Saver?

Fixing your servo saver becomes necessary when you face non-stop problems. For example, nuts coming loose, servo steering twitches, etc. If the servo saver is broken or fully damaged, you have to look for a replacement.

There are a lot of new and improved servo savers on the market as of now. You can go for any of those ones and ditch your damaged servo saver. 

But if the servo saver just needs troubleshooting, for example, tightening, you can easily do that. For that, you’ll need some Loctite at the nut. Also, you can use 2 nuts. Just make sure that you tight the servo saver well. 

See the above tighten servo saver section for more details. So, that’s how you can either replace or fix your servo saver.


What Is the Purpose of a High Torque Servo Saver?

A high torque servo saver provides support to the internal gears of the servo. The all-new spring mechanism allows the servo saver to absorb the impact of heavy driving. Along with the shock absorption, this unit also offers a brilliant-looking design. So, it checks all the boxes perfectly.

How Does Servo Saver Work?

Servo saver mainly works as a shock or impact absorber for any RC vehicle. It uses several springs and durable components to take the impact onto itself. That way all the extra stress does not go to the servo. As servo is a crucial unit for any RC, a servo saver provides protection to it.

What is Servo Saver Spring?

A servo saver spring is a durable spring for servos saver. Exclusively made for metal servos, these springs have an extreme tolerance for rocky roads. Because of that your servo can go past its limits and take more heavy impacts. So, for a crisp steering experience, servo springs are unparalleled.


That’s all I had on RC servo saver installation and troubleshooting. Now, you can easily assemble, tighten, install and fix the issues of your servo saver.

If you have any queries, feel free to let me know.

Until then, have fun with your RC after adding the servo saver!

About The Author

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top