Traxxas Receiver Won’t Bind

Traxxas Receiver Won’t Bind: Here’s How To Fix It!

Introduction

If receivers don’t bind with the transmitter, the car won’t start. It’s a problem that makes users want to tear their hair off. That’s where we come in. We’ll help you fix this issue.

The main question is, why Traxxas receiver won’t bind?

There can be multiple reasons behind it. There might be issues with your battery. The frequency may be wrong. Antennas might be causing interference. It’ll be a good idea to check if the receiver is working with another RC. Your servos might have stopped working.

This is just the gist of the problems. However, if you want to know more, spare us a minute. You’ll need to have more in-depth knowledge.

Without further ado, let’s begin!

Traxxas Receiver Won’t Bind: 6 Easy Solutions

It’s never easy when receivers stop working. We must extensively analyze them in order to pinpoint the cause of the problem. Follow the steps below to troubleshoot the issue-

Checking Servos

It’s possible that the issue isn’t with the radio system at all. But with one or more of your servos. Is your RC reacting to some orders from the transmitter and not all? Then your servos have problems. Checking them with a good servo tester would be the way to go.

Solution

Check if the servos are properly plugged in the receiver. You can even try plugging it in the receiver you know is functional. If it’s still not working, you’ll need to fix the servo issues. 

There’s a chance you’ll have to resolder the wires from the servo into the circuit board. If this job is too complex for you, hire a professional.

Checking the Batteries

Sometimes the batteries might prevent your traxxas receivers from binding. It’d be best to check if there are any issues with them.

Solution

Double-check that the batteries are properly placed. Even one wrongly inserted battery might create issues.

If your Traxxas has been lying unused for a while, please check the batteries for corrosion. 

It’s a good idea to remove the batteries if the devices won’t be used for a while. In that way, you can extend the battery life. Another way to do that is learning how to charge Li-Po batteries properly.

Replace the batteries in the RC and the transmitter with new ones. Even nitro RCs require a battery pack to power the electronics inside.

While we are on the subject of batteries, here are some of our top picks-

Product 1 Product 2

You now have an idea about good batteries. Let’s proceed with the steps.

Examining the Transmitter

The main issue could be the transmitter itself. It’ll need to be diagnosed to make sure it’s okay.

Solution

Do you have another Traxxas lying around that uses the same frequency as the transmitter? Try using it with the other vehicle. You’ll then be able to tell which one is causing the issue.

Is your transmitter working with the other RC? Then the main issue is with your receiver. One possible reason could be it’s too close to the transmitter. Try putting some distance between the two. In that way, you can get a better signal, and the receiver may just bind.

Finding Antenna Issues

Antennas are very important. It’s through them the signal flows between the RC and the transmitter. If you’re wondering if you can bind any receiver to any transmitter, it’s possible. However, you must be able to change the antenna when transmitting.

There are antenna relays available for this reason. They will perform the transition for you automatically.

Solution

If your transmitter has a telescopic antenna, make sure it’s completely stretched. See if your Traxxas’s reception antenna fits correctly.

Check to make sure if the antennas aren’t twisted or damaged. Or if they are not touching any of the metal parts in your car. 

Inspecting the ESC

A lot of times you’ll see the receiver isn’t binding because the ESC is compromised. It might not be calibrated, for example. 

Solution 

Check to make sure the ESC three-wire cables are linked to your receiver. 

In some cases, you’ll see the ESC isn’t connected to the receiver at all.  If that’s the case, you’ll have to connect esc to receiver. After that, please calibrate your ESC.

After properly connecting the two together, check to see if the receiver is binding now.

Locating Frequency Problems

Sometimes frequencies and receivers don’t compliment each other. You need to make sure that they are on the right page. Did you buy the car and the transmitter separately? Frequency crystal in the RC’s receiver might not match the crystal’s one in the transmitter.

Solution 

It’ll be a good idea to check if there was a mix-up. Sometimes wrong transmitters are put in the box by mistake. If there wasn’t, check if the receiver and the transmitter are on the same wavelength. 

Traxxas cars have a fixed frequency of 27 MHz. Are you using the car with the selectable bands? Ascertain that the car and the receiver are on the same frequency.

These are the steps you’ll need to undertake to make sure your Traxxas receiver binds.

FAQs

Question: What is the best Traxxas receiver?

Answer: There are some really good receivers available on the market. You could try Spektrum or Futaba receivers. FLYSKY receivers are also making a name for themselves.

Question: How expensive are the receivers?

Answer: It depends on which receivers you’re planning to buy. High-end receivers like Spektrum will cost you around $350-400. Lower ends will cost you $20 to $60.

Question: What’s the difference between FHSS and DSSS receivers?

Answer: HSS activates three channels at the same time and hops between them to prevent interference. DSSS has a larger bandwidth to avoid interference and detection.

Conclusion

That’s all we have for you today when it comes to why Traxxas receiver won’t bind.

Always remember not to panic. There is always a solution to every problem. Hope we were able to fix all your issues with our guide.

May we see each other again. Until next time, stay safe and good luck!

About The Author

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top